| About This Archive | | DCHAS-L 2014 Index | | DCHAS-L Yearly Index | |
Check out Safety Emporium for your N95, N99, and face shield needs.
|
Previous by Date: Subject: Re: [DCHAS-L] Chemical Fume Hood Evaluation Form Date: Thursday, November 20, 2014 9:31:52 AM Author: Ray Cook <raycook**At_Symbol_Here**APEXHSE.COM> |
Next by Date: Subject: Re: [DCHAS-L] Chemical Fume Hood Evaluation Form Date: Thu, 20 Nov 2014 19:02:01 -0500 Author: Bruce Van Scoy |
We do an ASHRAE 110 test on every new hood installation (including renovations) at UC Davis. It's a very good way to make sure the laboratory airflow control system is working properly.
Here's the link to our Campus Standards and Design Guide: http://dcm.ucdavis.edu/cdg/index.html It's in the Part III Construction Divisions. Fume hoods in Division 11 - Lab Airflow in Division 23. 23 09 10 has lab hvac details.
Hope this helps,
Debbie
Debbie M. Decker, CCHO
Safety Manager
Department of Chemistry
University of California, Davis
122 Chemistry
1 Shields Ave.
Davis, CA 95616
(530)754-7964
(530)304-6728
dmdecker**At_Symbol_Here**ucdavis.edu
Birkett's hypothesis: "Any chemical reaction
that proceeds smoothly under normal conditions,
can proceed violently in the presence of an idiot."
-----Original Message-----
From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of Wayne Wood
Sent: Thursday, November 20, 2014 5:48 AM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] Chemical Fume Hood Evaluation Form
Thank you for the references and wise advice, Bruce. I agree 100% with your recommendation about linking periodic evaluations to the designed performance test - given the variations in face velocity that have been shown to be acceptable we don't really have a choice.
The question I am wrestling with now is whether factory containment tests are adequate or whether we have to do field containment tests like ASHRAE 110 at the time of hood commissioning.
W.
-----Original Message-----
From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of Bruce Van Scoy
Sent: Wednesday, November 19, 2014 6:13 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] Chemical Fume Hood Evaluation Form
W.,
I am not familiar with a comprehensive standardized form for the evaluation of chemical fume hoods.
Some of the better guidance that I have found is available at the two links listed below.
I would strongly recommend that the designed performance specifications be specified initially with the periodic evaluations completed to verify that the hoods are actually performing as designed. My personal experience is that inadvertent maintenance or user activities have negatively affected the routine performance requirements, usually due to the maintenance worker or employee not realizing the impact of seemingly "minor" modifications. I like using smoke tubes to educate employees on the impacts and results of these "seemingly minor modifications" with verbal coverage of what needs to be obtained/maintained. We can't be in every lab all of the time and I've had good results of laboratory workers recognizing potential hazards and getting EHS involved when they are not sure based upon these practices, once
they have been educated.
Please see:
http://orf.od.nih.gov/PoliciesAndGuidelines/Bioenvironmental/Documents/SECTI
ON15991CONSTANTVOLUMEJune2007_508.pdf
http://orf.od.nih.gov/PoliciesAndGuidelines/Bioenvironmental/Documents/SECTI
ON15992VARIABLEVOLUMEJune2007_508.pdf
My $0.02 - based upon numerous negative/positive trials and errors over the years!
Bruce
-----Original Message-----
From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of Wayne Wood
Sent: Wednesday, November 19, 2014 4:26 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] Chemical Fume Hood Evaluation Form
Smart people ask good questions. Good questions, Ralph.
Ralph, I was looking mainly for a basic chemical fume hood evaluation and inspection checklist which could be used by an EHS technician once or twice a year but you and Kim Gates, who replied privately, have expanded my
horizon somewhat.
You asked:
What aspect of a fume hood are you interested in evaluating:
- the design of the hood itself
I wasn't thinking of that but Kim got me interested in a commissioning checklist. It would be hard to do periodic evaluations without data on commissioning, such as the performance specs at the time of installation.
- its containment?
ASHRAE 110 appears to be the way to go, this is something that would fit well in a commissioning checklist.
- how it's being used?
Yes, insofar as we would want to identify uses that compromise the hood;s operation, like clutter and or heat or other turbulence-generating activities.
- whether it's operating as designed relative to the general ventilation system in the lab?
That would be more difficult to check. I won't pretend that is something we systematically follow up on in my institutions; I'm curious to know what others are doing?
I think that these would require distinct forms?
Yes, and in some cases the persons completing the forms might need different competencies as well.
W.
- Ralph
Ralph Stuart, CIH, CCHO
Chemical Hygiene Officer
Keene State College
ralph.stuart**At_Symbol_Here**keene.edu
Previous post | Top of Page | Next post